8.0 PIN USAGE EXAMPLES
The following tables highlight two possible configurations for the DLP-2232H module. There are
numerous additional combinations available. For the complete DLP-2232H pin list refer to the
pin descriptions in section 2.0.
CASE 1: Port A: 245 FIFO Synchronous, Port B 245 FIFO Asynchronous
PI N #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
19
20
P O R T A P A R A L L E L S Y N C , P O R T B P A R A L L E L A S Y N C
S I G N A L U S A G E D E S C R I P T I O N
SIWUB –The Port B Send Immediate / WakeUp signal combines two functions on a
single pin. If USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in
the EEPROM, strobing this pin low will cause the device to request a resume on the USB
Bus. Normally, this can be used to wake up the Host PC. During normal operation
(PWREN# = 0), if this pin is strobed low any data in the device TX buffer will be sent out
over USB on the next Bulk-IN request from the drivers regardless of the pending packet
size. This can be used to optimize USB transfer speed for some applications. Tie this pin
to VCCIO if not used.
PORT B WR# - When taken from a high to a low state, WR reads the 8 data lines and
writes the byte into the FIFO’s transmit buffer. Data written to the transmit buffer is sent
to the host PC within the TX buffer timeout value (default 16mS) and placed in the buffer
that was created when the USB port was opened.
PORT B RD# - When pulled low, RD# takes the 8 data lines from a high-impedance
state to the current byte in the FIFO’s buffer. Taking RD# high returns the data pins to a
high- impedance state and prepares the next byte (if available) in the FIFO to be read.
PORT B TXE# - Transmit Buffer Empty: When high, do not write data into the FIFO.
When low, data can be written into the FIFO by toggling WR. During reset this signal pin
is tri-state. Data is latched into the FIFO on the falling edge of the WR pin.
PORT B RXF# - Receive Buffer Full : When low, at least 1 byte is present in the FIFO’s
receive buffer and is ready to be read with RD#. RXF# goes high when the receive buffer is
empty. During reset this signal pin is tri-state. If the Remote Wakeup option is enabled in the
internal EEPROM, during USB Suspend Mode (PWREN#=1) RXF# becomes an input. This can
be used to wake up the USB host from Suspend Mode by strobing this pin low for a minimum of
20ms which will cause the device to request a resume on the USB bus.
PORT B DB7 – Port B FIFO Data Bus Bit 7
PORT B DB6 – Port B FIFO Data Bus Bit 6
PORT B DB5 – Port B FIFO Data Bus Bit 5
PORT B DB4 – Port B FIFO Data Bus Bit 4
PORT B DB3 – Port B FIFO Data Bus Bit 3
PORT B DB2 – Port B FIFO Data Bus Bit 2
PORT B DB1 – Port B FIFO Data Bus Bit 1
PORT B DB0 – Port B FIFO Data Bus Bit 0
GROUND
GROUND
EXTVCC - Use for applying main power (4.5 to 5.25 volts) to the module. Connect to
PORTVCC if the module is to be powered by the USB port (typical configuration).
PORTVCC - Power from the USB port. Connect to EXTVCC if the module is to be
powered by the USB port (typical configuration). 500mA is the maximum current
available to the USB adapter and target electronics if the USB device is configured for
high power.
Rev. 1.1 (May 2011)
10
? DLP Design, Inc.
相关PDF资料
DLP-2232ML-G MODULE USB ADAPTR FOR FT2232D LP
DLP-2232MSPF MODULE USB ADAPTER WITH MCU
DLP-CB-DLPC200-10R BOARD CONTROLLER FOR DLP
DLP-D-G MODULE USB SECURITY DONGLE
DLP-HS-FPGA2 MODULE USB ADAPTER FOR FT2232H
DLP-IOR4 MODULE LATCHING-RELAY 4-CH
DLP-TEMP-G MODULE DATA-ACQUISITION 3-CH
DLP-TXRX-G MODULE USB-TO-TTL SRL UART CONV
相关代理商/技术参数
DLP-2232H-PSOC5 功能描述:界面模块 USB+ Microcontroller Development Module RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-2232H-SF 功能描述:界面模块 USB Micrcontroller FPGA Module RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-2232M 功能描述:界面模块 Multi-Mode UART/FIFO RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-2232M-G 功能描述:界面模块 Multi-Mode UART/FIFO RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-2232ML 功能描述:界面模块 Low Profile 2232M RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-2232ML-G 功能描述:MODULE USB ADAPTR FOR FT2232D LP RoHS:是 类别:编程器,开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
DLP2232ML-G 功能描述:界面模块 Low Profile 2232M RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-2232MSP 功能描述:界面模块 USB to MSP430 w/ FTDI FT2232H RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度: